we also got this valve box that goes over our ball valve and once we fill it in with dirt and we need to work on it later we’ll be able to loop the lid right here and get in and turn off our water without having to mess around with digging it all out trenching is the most time-consuming and physically demanding part of this job do-it-yourselfers you’re gonna want to get several friends to help you dig so there’s a backflow prevention device this is a pressure vacuum breaker or a PV B now
most cities or water districts require some kind of effective prevention device when you’re installing sprinkler systems because it keeps contaminated water from flowing back into your drinking water source so whether use an anti siphon or pressure vacuum breaker we recommend some kind of backhoe prevention all right so now that we’ve installed our ball valve and our mainline we can turn the water onto the rest of the home as you can see the roots on this property posed pretty significant challenge so what we did is removed one the way of our valve wire make sure to use schedule 40 PVC pipes between the pointed connection and the inlet set of valves alright this is a premium manifold kit from sprinkler warehouse attached to our valves here we’re using that in our in our irrigation system for this home now for this as opposed to hard piping it in this is much faster and easier to replace and to install take it in now you do move in the premium kit right there but if you need to replace the valves it’s as easy as this you dig it up you unscrew it you pop out one valve bring in another valve that is a lot quicker than having to glue and to cut this entire thing apart in back together.
if you’re trying to replace your valves or even just installing them just screw it on and you’re good to go after the valves because there’s a lot less water pressure it’s safe to use class 200 pipe to feed the sprinkler heads and that can save you a little bit of money to run the pipe under the driveway we recommend using a water-powered boring kit that we have a sprinkler warehouse what you do is you put a high-pressure nozzle at the end of your class 200 pipe and you slowly push it in there and the water pressure pushes the dirt all the way creating a tunnel for the pipe to go through and then just connect that to the rest of your system so if you were to have your sprinkler head attached to an old-school nipple riser like this and never get run over by a vehicle or a really heavy riding lawnmower you would probably break your nipple riser possibly break your sprinkler head and even worse break your PVC pipe.
this swing joint right here completely prevents that as it’s flexible and it can move at the joints and it also makes it easier for adjusting the height of your sprinkler head just in case the grass clippings were to change the height of the ground right there you just dig it up put a little dirt underneath it and swing it up a little bit and adjust at the joints here we are with our our wire this is direct burial wire which means we do not have to run a conduit in order to bury this underground we got three red wires right here for our three valves right over there we have some obstacles in addition to everything else here in this yard and I’m standing on this sidewalk right here is actually a big obstacle for our wires and our piping we’ve gone underneath it right here with a conduit and some water pipe as well and we’re gonna run our red wires and one common wire through this one piece of PVC pipe to our valves and all the way around to the backyard and to our controller that’s inside the garage so this right here there’s a little coil now what this does is as it adds a little bit of a extra protection against power surges boom coil and you do that to all of them in order to avoid electrical shorts when connecting the direct burial are to the valve wires make sure to use waterproof silicone filled wire connectors so you want to overfill your trenches when you’re filling them back in otherwise when the soil gets wet and begins to settle it’ll sink down a little bit you want to tamp it down to get a nice and compact that way you don’t leave any signs of trenches in your yard so facing the bed a crush rock under your valves can help
with drainage and provide a nice solid
foundation in case anything heavy ever
rolls over on top of it so here I am at
the eave the house installing this rain
the sensor we want this to be above where
the sprinklers are going to be spraying
because we obviously don’t want water to
get into here otherwise, it’s going to
turn off her controller
now in order to protect your wires from
the damage you don’t want to run it through
some PVC conduit from where it comes out
of the ground all the way to your smart
control next we’ll flush the cyst and
open the test on the backflow
the device leaves the air and makes sure to
turn the water on very slowly at the
backflow preventer to avoid any pipeline
damage alright now we got all the wires
running to our controller we have our
rain sensor wire right here we’re gonna
hook that up we got our common wire
we’re gonna hook that up as well we’re
gonna turn the power onto this thing and
then what we’re gonna do is we’re gonna
strip the red wires one by one and we’re
gonna touch them to a powered terminal
what that’s gonna do is gonna start to
isolate which wire goes to which zone
because we don’t know which wire goes to
which zone at this point so if we turn
on terminal number one and start
touching a wire to it what was gonna
happen is it’s gonna turn on one of the
zones in our yard so let’s just say it
turns on zone number five then we know
that that wire goes to zone 5 so we’ll
count 1 2 3 4 5 and we’ll connect it to
zone 5 over here and we’ll strip another
wire touch it to the power terminal and
go on down the line until we know which
the wire goes to which zone and then we
connected to that corresponding zone
Rainbird is applied to all the sprinklers
for this install today we’re using Rain
Bird variable arc rotary or our vans and
a chi or high-efficiency van spray
nozzles now they all come in a variety
of throw distances so here we got the
Rain Bird our van adjustable rotary
nozzle these are our van 14s 18 and
24 those numbers indicate how far these
actual nozzles can throw water so the 24
is gonna shoot 24 feet
the ATS gonna shoot up to 18 feet and
the 14 up to 14 feet and you can adjust
it’s down if you only need to throw it a
a little bit less than that
all right I just installed the H event n
now that’s a spray novel that shoots up
to ten feet and can cover an entire 360
degree plane but it’s adjustable down to
the angle that you need we’re in the
center of a flower bed here so we’re
gonna go full 360 and it’s not quite ten
feet wide so we’re gonna do maybe about
six or seven-foot on this alright so
here I am in front of two nozzles that
are right next to each other now why
would we need two nozzles right next to
each other we’re gonna want to water our
flower bed every day except for the days
when the yard goes off when the yard is
being watered that’s gonna cover the
flower bed as well and we’re not gonna
need to have this one running so we’re
gonna use our controller to program it
to make sure we get exactly the kind of
the water we need so let’s take a look at
this achieve an eight right here now H E
stands for high efficiency this one is
12 inches high that way we can go over
our flowers and cover our entire flower
beds and then over here we’re gonna put
the arvan eighteen in and that is gonna
shoot at 18 feet covers both the flower
bed and the rest of the yard all the
grass and everything – let’s get that on
here just unscrew stick that in there
there we go get that on there
and that’s how that goes that’s why you
have two of them right here alright so
now we’re gonna adjust this sprinkler
heads they might not be pointed in the
right direction and they might be so
over-spraying have a wide-angle we’re
gonna try to make that angle be just
right for this flowerbed so first we’re
gonna adjust it this way the Rain Bird
our van and a chi band nozzle spray
patterns and distances are easily
adjusted by hand without tools the
rotating stream technology delivers wind
resistant large water droplets without
misting or foggy and water usage is
reduced by about 33 percent is
money in your pocket remember sprinkler
the warehouse has everything for your
irrigation needs so your trees lawn
flowerbed and gardens are lush and
beautiful and if you have any questions
remember to speak to one of our superb
customer service agents on sprinkler
warehouse.com
they really know their stuff and they
will get you squared away
subscribe to our YouTube channel for
helpful tips tutorials and general
sprinkler instruction I’m Francisco
your sprinkler warehouse pro see you
later irrigator
LAWN CARE SPRING SPRINKLER REPAIR
https://www.google.com/maps?cid=12943596387042468960
https://search.google.com/local/writereview?placeid=ChIJp9BOM2zNQIYRYCSy_VXkoLM
how to install a sprinkler system, how to install a sprinkler system in houston tx, how to install a sprinkler system in spring tx, how to install a sprinkler system the woodlands tx, how to install a sprinkler system in cypress tx, sprinklers system, sprinkler system, sprinkler systems, installation of sprinkler systems, installing sprinkler system, sprinkler system for lawn, sprinkler system install, sprinkler system installation, sprinklers systems installation, lawn sprinkler system, lawn sprinkler systems, sprinkler system installers, sprinkler system lawn, sprinkler systems for lawn, sprinkler systems for lawns, sprinkler systems installed, lawn sprinklers systems,